MOTIP - Alu zinc spray

Full specifications

MOTIP - Alu zinc spray

MoTip Alu Zinc Spray for zinc-plated parts and surfaces, which have been damaged by welding, sanding, drilling, transportation etc., and which have to repaired or adapted to colour shade.

Also suitable as excellent corrosion protection for metal surfaces and blanc iron metals. Suitable for only a limited extend on aluminium

• Excellent corrosion prevention
• Heat-resistant up to 250°C
• Resistant to changing temperatures
• Good flow
• Fast Drying
• Excellent adhesion
• Spot weldable
• Good coverage
• Resistant to petrol, chemicals and weather influences

• Basis of the binder: Epoxyester
• Colour: silver-metallic, similar to galvanizing
• Smell: solvent
• Degree of gloss: satin matt, not measurable as metallic
  
• Efficiency:
  Depending on consistence ans color of the ground:
  400 ml are sufficient for approx. 1,25-1,75 m² at covering layer
• Drying time (at 20°C, 50% relative air humidity):
  Dust-dry: after approx. 15 minutes
  Tack-free: after approx. 20-30 minutes
  The drying time depends on surrounding temperature, air humidity and thickness of the applied coat.
• Temperature resistance: up to 250°C
• Storage stability:
  10 years if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%)
• Size:
  aerosol can, maximum nominal volume 400 ml

INSTRUCTION MANUEL

Before use, carefully read and observe the warning texts on the label!

• The ground has to be clean, dry and free from rust and fat.
• Shake can vigorously for approx. 2 minutes.
• Test spray at an invisible spot.
• Apply several covering coats.
• Spray from a distance of approx. 25 cm.
• It is not recommended to overpaint with other laquers.

TIPS FOR SPRAY PAINTING

Protect the object and the surrounding area from spray mist. When painting small areas it is recommended that a piece of card is used as a mask, with a hole cut in it slightly larger than the area to be sprayed. The mask should be held 1 to 2 cm from the surface. With this method, the mainly part of the spray mist is brought under control. It recommends to mask parts not to be lacquered, to protect the surrounding against the spray mist.

The aerosol can should have room temperature.

Temperature should range between +10°C and +25°C, max. air humidity 60 %.

Store in a dry place. Protect from direct sunlight and other sources of heat. Use only during dry weather, in places protected from the wind, and in well-ventilated rooms. Follow the warning texts on the labels! 

---

WARNING:

GHS02 - flame	GHS07 - Eye Irrit	GHS09 - Environment

• H222 - Extremely flammable aerosol.

• H229 - Pressurised container: May burst if heated.

• H319 - Causes serious eye irritation.

• H336 - May cause drowsiness or dizziness.

• H411 Toxic to aquatic life with long lasting effects.

• P101 - If medical advice is needed, have product container or label at hand.

• P102 - Keep out of reach of children.

• P210 - Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.

• P211 - Do not spray on an open flame or other ignition source.

• P251 - Do not pierce or burn, even after use.

• P260 - Do not breathe spray.

• P410+P412 - Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F.

• P501 - Dispose of contents / container in accordance with regional regulations.

• EUH066 - Repeated exposure may cause skin dryness or cracking. 

For download

Safety data sheet

Sicherheitsdatenblatt